Beginner Basics • Re: Can't connect to router board via ssh
10.10.2.0 is not a valid IP address for a port/interface?Valid addressed are w.x.y.z where z is in the range 1-254, 0 is reserved "network" and 255 is reserved "broadcast".Try setting it to 10.10.2.2...
View ArticleRouterBOARD hardware • Re: CCR2004-16G-2S+PC NO USB, WHYYY!??
Hi there.I just want to share my frustration with the CCR2004-16G-2S+PC. I was super excited about it when I first saw it on the YouTube channel and now I have one. Currently I have a RB5009 running...
View ArticleUseful user articles • Re: mDNS between VLANs with just bridge filters - Look...
Hi everyone, thanks for sharing, I put this setup in the routerboard, it works, but it doesn't find the Sonos soundbar, it only finds all the chromecasts. any suggestions?Statistics: Posted by Kataius...
View ArticleRouterBOARD hardware • Re: Hex PoE to HAP AC boot fail - POE Overload issue
Since this is 1st result from Google I'm going to give some background: it will not work. The hAP ac resistance is too low per MT support (https://www.reddit.com/r/mikrotik/comme ... c/j3x8e1m/):The...
View ArticleGeneral • Forcing source ip and/or route
I'm not sure how to properly express this. I had a problem that I tried to solve with various combinations of src-nat and routing policy, failed, and then fixed it by doing it properly - which means...
View ArticleBeginner Basics • Re: Clients not choosing "best" AP?
Hi, thanks for your reply and that you share your experience on this.Are the radios transmitting on different channels (preferably 2412, 2437 and/or 2462)?My experience is that the channels are equal...
View ArticleGeneral • Re: NAT with several public IPs
If the other WAN addresses are not router towards your NAT device[*], then you need to set those addresses explicitly on WAN interface. NAT only kicks into action after packet was already delivered to...
View ArticleGeneral • Router OS 7.14.2 DHCP Relay not working
Good evening all, I have a mikrotik CRS3328-24p-4s+ running. I have installed a new windows server which I am going to be using to do the DHCP and the DNS. The DNS I am working fine, however in...
View ArticleWireless Networking • Re: Which bluetooth
I'd say that ROS only supports BT hardware vased on chipsets akso used by hardware made by Mikrotik. I could only find references to Quectel's BG77 in this context. So I guess that if you find a BT...
View ArticleBeginner Basics • MikroTik Fiber-to-Copper converter FTC11XG
Dear allI just received MikroTik Fiber-to-Copper converter FTC11XG and I spent more than three hours trying to figur out to configure it with DFP-34X-2C2 stick it is little bet complicated device at...
View ArticleWireless Networking • Re: Antenna showdown with my Nano VNA
When using polarized antennas (they all are) it's important to perform measurements when polarization planes of both antennas match exactly. If using 2 chains on one side and both antennas are at some...
View ArticleSwOS • Re: Weird: Monitoring EGRESS traffic of a trunk port does not show...
Hello robertkjonesjr,thanks again for your detailed thoughts.In the beginning I indeed faced some additional challenges trying to monitor the switch on the same wire where also network traffic is...
View ArticleWireless Networking • Re: configure "cAP ac" to...
For one it very much depends on ROS version running on both devices. In addition it depends on which of optional packages are installed on cAP ac. After you provide this information, we can go...
View ArticleBeginner Basics • Re: MikroTik Fiber-to-Copper converter FTC11XG
FTC11XG is a SwOS device so it provides very little management possibilities by itself. Since your SFP module is ONU, it needs quite some configuration (and that can't be done via SwOS). The only...
View ArticleRouterBOARD hardware • Re: CCR2004-1G-2XS-PCIe Problems
may i ask please, if your computer reboots when you restart the card - or that happens only with HP/DELL like servers?Thanks!Statistics: Posted by wpeople — Sun Mar 31, 2024 12:32 pm
View ArticleRouterBOARD hardware • CRS317 vs CRS326 Performance
Dear experts,I am unsure which device to buy - from a performance perspective of a L1/L2...
View ArticleWireless Networking • Re: hAP ax3 wireless problem
Addendum: I don't remember which countries this is true for, but in my testing hAP ax3 seemed to really love 5500/Ceee when frequency was unset.Can confirm this true on wifi-qcom-ac, country Austria...
View ArticleRouterBOARD hardware • Re: CRS317 vs CRS326 Performance
For L2 they both do wirespeed on all ports simultaneously. Difference is in bridging (software L2, usually not necessary) and routing.Statistics: Posted by mkx — Sun Mar 31, 2024 1:24 pm
View ArticleGeneral • SMB share cannot be accessed after upgrade
I upgraded my Mikrotik cAP ac to version 7.14.2 yesterday (don't remember which exact version I had before that). After the upgrade, I noticed that I cannot access the default SMB share /flash/pub,...
View ArticleWireless Networking • wifi reauthenticating
I have a task scheduled at 5:00 that disables and enables a Wi-Fi interface in case it has changed channels due to radar interference. After executing it, I have an iPhone that often cannot connect to...
View Article