Forwarding Protocols • Re: VOIP IPv6 UDP packets are lost form WAN to LAN
To me, it looks like the packets are being dropped at the bridge.Do you have any firewall rules configured on the bridge itself (separate config from the firewall)?Also, make sure the bridge settings...
View ArticleGeneral • Wireguard Keeps trying to reconnect
7.14.1 changelogs : wireguard - do not attempt to connect to peer without specified endpoint-address;But it seems still not fixed in 7.14.2,when i disconnect from my android phone,the router will log...
View ArticleGeneral • Re: Internet speed cut in half after Hex, direct to modem gets full
Did OP fix this or return the router and get something else? I'm having the exact same problem. I have even tried disabling all firewall rules just to be sure (I'm running factory defaults anyway)....
View ArticleWireless Networking • Point to point link, Audience, wifi (wifiwave2)
Good morning,I really hope you can help me.We have two Mikrotik Audiences, we use wifi2 on both devices as a dedicated link between them.Previously we had Audience1 as AP and Audience2 as...
View ArticleWireless Networking • WIFI networking crashes after change to AX device
So far I used a cAP ac to which a mAP light was connected via a "station bridge" as a "wireless cable".Now the cAP ac was swapped for a cAP ax.Yes, I read the note late but that "station bridge"...
View ArticleBeginner Basics • Fresh DHCP Client Test
I factory reset an L009 and do QuickSet router mode, and I run DHCP Client and attach it to interface 'bridge' - and I don't get an IP.I have a device connected to ether8 and it's assigned an IP just...
View ArticleWireless Networking • Re: WIFI networking crashes after change to AX device
I face this very same issue. I assume it's because of station-pseudobridge causing a loop detection. Maybe try protocol-mode=none on your cap ax bridge.Statistics: Posted by infabo — Sat Mar 30, 2024...
View ArticleBeginner Basics • Re: VLAN'ising an existing configuration without disrupting...
Ok, so far this is being extremely helpful /s.I wonder if there's some workflow involving safe mode and/or a timed saved config restore script that would let me make progress without having to take a...
View ArticleGeneral • Re: Watchdog, or alternative?
Does this look good:Code: /system watchdogset auto-send-supout=yes ping-start-after-boot=10m ping-timeout=2m send-email-from=joseph@xxxxx.com \ send-email-to=joseph@xxxx.com...
View ArticleWireless Networking • Re: Point to point link, Audience, wifi (wifiwave2)
This was to resolve airtime being wasted with multicast traffic, being sent at a much lower data rate.Although this has resolved issues of hung webpages, the throughput has gone down from 400Mb+ to...
View ArticleWireless Networking • LHG R modem upgrade from LTE6 to LTE18
Hello,Currently, I have an R11e-LTE6 modem in my LHG R. I have the opportunity to purchase a used Telit LM960 modem. Does any of you dear colleagues have experience with replacing the modem in this...
View ArticleBeginner Basics • Re: Fresh DHCP Client Test
Post your config please. Also tinkering with quickset and then tinkering with settings in other menus can cause unwanted behaviour. If you reset router to factory default then default configuration...
View ArticleBeginner Basics • Re: cAP ac Multiple SSID
I wonder if it is right that there is no IP assigned directly to ether1. 192.168.0.200 is assigned to Base_VLAN.Statistics: Posted by SanchoHa — Sat Mar 30, 2024 5:10 pm
View ArticleRouterBOARD hardware • USB Device Lives On & Not Able to Be Removed
After removing my mobile phone from Microtik CCR1036-12G-4S, USB port, the RouterOS always show it, no matter i reboot CCR1036,shut if off and turn on, reset USB power, restore whole system from...
View ArticleClik here to view.
General • Problem with slow DHCP after migrating to Mikrotik switches
Hi,I'm trying to figure out what is going on.After migrating whole network infrastructure to Mikrotik switches (CRS354 & CRS326) I am observing extremely slow DHCP performance.It takes over 30-40...
View ArticleRouterBOARD hardware • Re: USB Device Lives On & Not Able to Be Removed
This is the "usb root hub", the router side of the USB bus. It was always there, also before you connected your phone. You cannot remove it.Statistics: Posted by pe1chl — Sat Mar 30, 2024 5:39 pm
View ArticleGeneral • Re: Bandwidth usage per IP
i tried to run on SXTsq Lite5 AC [6.48.6 (long-term) ]. i tried but i failed to setup this. I don't where i am getting stuck. No report generated. Can you please provide a video tutorial how to set it...
View ArticleScripting • Re: Is 8MB in a variable from a txt file is possible?
I suspect there is a bug on http-header-field argument for fetch command, maybe it is not sent correctly (I didn't check this over local web server to analyse), download data is always 64512 bytes...
View ArticleBeginner Basics • Clients not choosing "best" AP?
Hi,im running 2 CAP ACs with CAPSman (CAP 7.14.1 - wireless package, Capsman 7.14. RB5009), and I noticed, that some clients in my IoT Network, are not choosing the AP, which is providing the best...
View ArticleBeginner Basics • Can't connect to router board via ssh
Hello,I want to set up my router board but I can't connect to it. I added to my interface lan 2 (ether2) the ip-address = 10.10.2.0. After that I added the ip-address= 10.10.2.1 to the interface of my...
View Article