General • Assistance Needed with Multicast Configuration for MDNS Print...
Hi everyone,I'm currently facing a challenge with my network topology, which is attached for reference. Despite my efforts, I haven't been successful in activating multicast to enable the use of an...
View ArticleGeneral • Re: Assistance Needed with Multicast Configuration for MDNS Print...
For GRE tunnels, you may need to use PIM. See viewtopic.php?t=185669Statistics: Posted by Amm0 — Sat Jan 13, 2024 12:18 am
View ArticleClik here to view.
Beginner Basics • Re: cAP ac bricked even with netinstall
... Also noticed that resetting again device to factory defaults will prevent again the access to the device, even using MAC address in Winbox. In this situation the only way to proceed is to...
View ArticleGeneral • Re: Connection through WireGuard for a list of users
Understood, I figured it out. Needed to set /ip settings rp-filter=looseWorking configurationCode: /ip settings rp-filter=loose/interface wireguardadd listen-port=12321 mtu=1420...
View ArticleGeneral • CRS328-24P-4S failed to boot properly after update
Hi, CRS328-24P-4S did not start up properly after upgrading to 7.13.1.After booting, the network interfaces do not pick up. I connected with console cable I don't see only the following Code:...
View ArticleRouterBOARD hardware • Re: What RouterBOARD is capable of 2Gbps as a PPPoE...
I would first check with your ISP whether they support IPoE AKA DHCP. That will dramatically lower the overhead on the Mikrotik router.It is quite uncommon for ISP's to only use PPPoE on FTTP...
View ArticleUseful user articles • Re: USB Disk issue after hardware reboot
Can the script resolve the issue of mounting to a wrong position after a sudden reboot?I have several issues of this when the USB drive was mounted to a different name that containers won't start. As...
View ArticleBeginner Basics • Difference between Native vs explicit VLAN while interVLAN...
Hello,I hope you are well.I'm setting up my first MikroTik switch/router. I tried to pay as much attention as possible. That being said, being new here, I might have missed something. Kindly correct...
View ArticleClik here to view.
General • Re: Multicast not working for ISP TV BOX (Vodafone)
The problem here is that the multicast server it's outside of Vodafone router , on mikrotik I was unable to route multicast traffic, but I bet that the suggested solution with some additional attempts...
View ArticleGeneral • Re: Firewall-dynamic firewall rules
Do not compare Mikrotik with Zyxell, it is not correct.In a router, firewall rules have their own order and it is important. The rules are enforced from top to bottom and nothing else. You are wrong!...
View ArticleBeginner Basics • V7.13.1 hAPax3 WiFi 'Configuration Profiles' doesn't seem...
I believe I'm doing something wrong, but what it is, I don't knowI've followed the manual instructions at https://help.mikrotik.com/docs/display/ROS/WiFi . I first created a security profile such as:...
View ArticleBeginner Basics • Re: DDoS help
The destination you obscured on the screenshot, destination port 65372, is it the IP of the Mikrotik itself or one of the NAT addresses?This is my public IP, so address of mikrotik router. Thanks a...
View ArticleGeneral • Re: Detected Arp Conflict
Check ARP Table for duplicate'sviewtopic.php?p=1043705&hilit=arp#p1043705Statistics: Posted by ToTheCLI — Sat Jan 13, 2024 7:50 pm
View ArticleBeginner Basics • Adguard container in AX3
Hello all my friends.I have a ax3 router with default configuration and default firewall.I setup adguard in a container from networkberg guide in youtube.I can login to adguard page with the ip i have...
View ArticleGeneral • Re: Mikrotik Hex-S + TP-Link Deco m4 Access Point not working.
I had to remove my older mikrotik devices from my network 951-2n,maplite,951Ui-2hnd, it seems like it does not like the Station Pseudo settings when operating as wifi ap clients to other devices, I...
View ArticleBeginner Basics • Why do the docs not mention adding "bridge" as...
I have an existing Cisco switch, and I've configured one of its ports as a Trunk port, with VLAN tagging using 802.1Q. I wanted to get that working with my Mikrotik RB4011iGS+RM, using ether1 as the...
View ArticleClik here to view.
Beginner Basics • Re: Why do the docs not mention adding "bridge"...
Because this is the official tutorial, those docs are an imposter --> viewtopic.php?t=143620Do agree though, the first article only notes tagging bridge for managment vlan, which is certainly true...
View ArticleBeginner Basics • Unable to access the router via L2TP
Hi all, I am often connecting to my router from the remote site via L2TP with IPsec VPN. I can connect access everything on my network except the router, so I looked into firewall rules to...
View ArticleGeneral • Re: Feature Request: Enhanced Fan Control Flexibility
Absolutely agree, my SFP modules idle at around 65C, which is fine as their operating range is between 0-70C. Having fans go full blast at such an unreasonable temperature is a bit.. cruel. Bumping up...
View ArticleRouterBOARD hardware • Re: Adding fan(s) to a CRS309
For those interested in adding fans, take a look at this video for some inspiration: https://www.youtube.com/watch?v=ZDTv6NGBhYkStatistics: Posted by kehrlein — Sat Jan 13, 2024 8:43 pm
View Article