General • Re: VLAN switching and routing with bonds
1) Default setting is frame-types=admit-all ... so if it's not changed explicitly according to needs, it'll remain that way.2) Do as you see fit. IMO access to management VLAN should be as restricted...
View ArticleAnnouncements • Re: WinBox v3.40 released!
anyone have an issue with version 3.40 of winbox and routeros 7 when logging in the session just disconnects? this only started when I upgraded to winbox 3.4Statistics: Posted by cobusv — Sun Mar 24,...
View ArticleGeneral • Re: wireguard problem with a v 7.14
Same here, after upgrade to version 7.14.1 both tunnels down. I hope this is resolved in the next version because the connection between two sites is downDid you already try 7.14.1 ?Does the issue...
View ArticleScripting • Re: Ansible 'expect' module like prompt response
Hello, i am struggling with sth similar. After resetting CHR to defaults any new cli shell prompts "Do you want to see the software license?". I need to answer N with Ansible. But its not...
View ArticleWireless Networking • Strange behavior with Mikrotik CAP AX - CAPsMANv2
Hello everyone,We have recently switched our wifi setup to all Mikrotik CAP AX. We are using CAPsMANv2 but we are experiencing some strange behavior in the following situations:1. FT and FT over DS...
View ArticleUseful user articles • Re: 📌 Tool: Using Splunk to analyse MikroTik...
Since all routers needs to be configured to have serial number (one time job), I have updated the main start page "MikroTik device list" ot show all routers who is sending data to Splunk using only...
View ArticleClik here to view.
Wireless Networking • Re: hAP ax3 wireless problem
It comes pre-configured in caps-mode from factory.I've just taken delivery of a cAP ac and I'm afraid it not configured in CAPs mode. It's definitely in router mode:Sure, it's not difficult to connect...
View ArticleGeneral • Re: CHR or Ethernet router?
Generally I'd guess that for higher throughputs using CHR on decent hardware would be more cost effective solution than using a powerful MT router. And I'd guess that single core CPU speed is the most...
View ArticleBeginner Basics • What happens to an interface that is not part of any bridge?
Hello all,I have a HEX-S router configured with two point-to-point links on ether1 and ether2, each connected to 2 upstream routers for redundancy.In my current setup I have removed the two ports...
View ArticleBeginner Basics • Re: What happens to an interface that is not part of any...
On layer2 interfaces are isolated. So possibility of leaking frames is slim. If frames do leak, it's probably due to errors in configuration.Also note that without special config, router will pass...
View ArticleGeneral • TIP: Do not use rp-filter=Strict with Dual WAN policy-based routing
Over the last few days I have tried to set up policy-based routing with a dual WAN setup. I used mangle rules to direct traffic to either one or the other WAN. Everything outbound appeared to work...
View ArticleGeneral • Re: Policy-based routing with dual WAN
Yup rp-filter=strict would do that. I can see how that how an esoteric /ip/setting like rp-filter might NOT be the first thought.FWIW, "strict" shouldn't be the default... so someone changed rp-filter...
View ArticleWireless Networking • Re: hAP ax2 station mode
Good news/bad news: good news is that my hAPax2 is failing to connect in station mode to a Cisco 11ax AP (9117) so it seems somewhat repeatable. Bad news is that my failure mode is slightly different:...
View ArticleGeneral • Re: TIP: Do not use rp-filter=Strict with Dual WAN policy-based...
Actually the learning point is dont change anything from defaults if you dont understand all possible ramifications.So glad the MT documentation makes it crystal clear NOT, with gobblity gook...
View ArticleGeneral • Re: CRS317 + CRS328 - InterVLAN routing with L3HW
I disagree with MKX, cannot recommend, in general, a switch for routing. The CRS317, can route up to about 400Mbps but thats it, so depending upon your internet connectivity????????The RB50009 is...
View ArticleScripting • execute & parse
The topic has been discussed many times, but everything is forgotten when there is little practice...Is it possible to access a variable whose name is not known in advance to the script function by...
View ArticleAnnouncements • Re: v7.14.1 [stable] is released!
user-manager experienced some strange errors with 7.14.1 after upgrade on a hEX.VPN users complained that they cannot log in, and i checked the logs:Code: 09:31:14 ipsec,error radius timeoutthen i...
View ArticleSwOS • Feature request - LACP rate change
HelloOn swos, we can't change lacp rate (fast or slow) in lag panel. Is it possible to have this setting ?RegardsStatistics: Posted by hhjklhjghjflkhgfomhf — Mon Mar 25, 2024 10:53 am
View ArticleScripting • Re: execute & parse
RouterOS is not a programming language.There are certainly simpler ways of doing things.Concrete and well-explained examples may have specific suggestions.Statistics: Posted by rextended — Mon Mar 25,...
View ArticleGeneral • Mangle and Queue Configuration for CAKE using Diffserve
At a suggestion from over on the Mikrotik reddit I'm posting up here my mangle and queue configuration for running CAKE queueing with diffserve. Please feel free to use and modify to your needs.This...
View Article