Wireless Networking • Re: Can hap ax2/3 and/or cap ax operate in 5ghz-an mode...
802.11an = wifi4 ?Can't test right now but normally it should be backwards compatible.Anyhow, 5ghz-an is in the list of possible bands to be used.Statistics: Posted by holvoetn — Sun Mar 17, 2024...
View ArticleBeginner Basics • IPv6 defconf ORCHID firewall rule is obsolete
add address=2001:10::/28 comment="defconf: ORCHID" list=bad_ipv6That ORCHID rule is obsolete, there is a new range 2001:20::/28 as per RFC7343. Use this instead:Code: /ipv6 firewall filter add...
View ArticleGeneral • Re: VLANs between Unifi and MikroTik
Hi,Is your configuration currently working? It looks a bit odd to me.I am assuming that you want the Hex to act as a switch and acquire a DHCP lease for itself on VLAN3, right?If so, I am not sure why...
View ArticleBeginner Basics • Guest network - vlan no internet access
Hi, I created a WiFi network for guests, dhcp works, it assigns me an IP, but I can't access the internet from this network, . I tried disabling firewall rules and bogons. Below I upload the...
View ArticleClik here to view.
Beginner Basics • Forum credentials reset
@ board admin:I registered on these forums a while ago and managed to loose my credentials, especially the forum user name.So I ran the "forgot my password" dialog (which involves my e-mail-address)...
View ArticleSwOS • Re: feature request - https for webui
+1 for https support in swosI manage a decent amount of swos devices. Not enough that I need to start looking for something that can be centrally managed (TR-069). routeros has to many features for...
View ArticleBeginner Basics • Re: Guest network - vlan no internet access
It's rather confusing to use the same names for your bridges (WHY MULTIPLE ??) as for some key-interface lists.WAN/ LANI strongly advise to rename them.And only use 1 bridge.Probably this part is in...
View ArticleBeginner Basics • Re: Forum credentials reset
You can best address your request to support@mikrotik.comStatistics: Posted by holvoetn — Sun Mar 17, 2024 12:58 pm
View ArticleBeginner Basics • CRS326 stuck waiting for installation server
My CRS326 went belly-up during a firmware update at least half a year ago. I was in a hurry and simply replaced it with another routing switch for the time being, and then life happened and I forgot...
View ArticleBeginner Basics • Re: CRS326 stuck waiting for installation server
I find a Linux VM helpful, as it simplifies the networking without needing you to reconfigure the host stack each time. I’ve posted detailed instructions for that, including a tip that might solve...
View ArticleWireless Networking • Re: Can hap ax2/3 and/or cap ax operate in 5ghz-ac mode...
Why?Does it have to be fixed, the standard is backward compatible and will be used by older devices.Band has to do with radio frequency.Statistics: Posted by erlinden — Sun Mar 17, 2024 1:41 pm
View ArticleGeneral • Re: Mikrotik Router as Firewall only, how to verify the source?
Sorry, I was probably a bit unclear. I have the 3 Ethernet Ports as shown in the Topologie that went to "Mikrotik-Firewall", one to the Router, one to the Clients Linux1 stands for and one to the...
View ArticleBeginner Basics • Re: IPv6 defconf ORCHID firewall rule is obsolete
I'm not sure about "instead". The old v1 protocol's reservation remains "deprecated" in the IANA IPv6 Special-Purpose Address Registry, so if traffic arrives at my router using an address from that...
View ArticleClik here to view.
Wireless Networking • Re: CAP AX - CAPSMAN- no DHCP lease [SOLVED]
For ax devices it is sufficient to set the device to CAP (reset with CAPs Mode). No manual settings on the CAP have to be done, unless you want "something" done with VLAN on the ethernet interfaces....
View ArticleGeneral • Re: v7.15beta broke backup file naming
Guys, we have rights to complain but I doubt they will revert the change and allow spaces in identity.So, what are the characters not allowed?Any suggestion to fix the identity name in scripts or get...
View ArticleRouterBOARD hardware • Re: The ACT LED means...what?
Not sure what it means, but I had a solid ACT light when I accidentally held down the reset button too long on my RB260GS, or something else went awry, and the switch went back to its 2.0p factory...
View ArticleWireless Networking • Re: Audience different revisions showing different...
The 4x4 radio only works from 149 up, from what I could tell.Statistics: Posted by gotsprings — Sun Mar 17, 2024 5:09 pm
View ArticleRouterBOARD hardware • Re: hAP ac , poe, RB962UiGS-5HacT2HnT
Unfortunately, no, this setup is not working.How long are UTP cables between RB5009 and powered devices?Statistics: Posted by mkx — Sun Mar 17, 2024 5:11 pm
View ArticleGeneral • Re: lo-Interface loopback
some kind of loopback-o-phobiaStatistics: Posted by baragoon — Mon Mar 18, 2024 10:36 am
View ArticleForwarding Protocols • Split subnet to smaller in a router with BGP
Good Morning,I have a router with BGP session to provider, this session announce a /24 subnet.Now if i assign the x.x.x.1/24 at eth1 this work fine, but if assign x.x.x.1/26 at eth1 and x.x.x.65/26 at...
View Article