Beginner Basics • Port forwarding to an ASUS router
Hello,I have a 5G MikroTik router (I believe the model is the MikroTik LMT 5G R16) provided by my ISP, which is linked via ethernet to an Asus RT-AX92U, which is then linked to my PC via ethernet. I...
View ArticleBeginner Basics • Re: No IP when Capsman and VLANS
You´re not alone. Exactly the same Problem here....Statistics: Posted by H4Y3 — Sun Feb 04, 2024 10:44 pm
View ArticleWireless Networking • Assistance Needed with Cube 60Pro ac Pair for Low Latency
Hello MikroTik Community,I'm reaching out to seek advice on optimizing my Cube 60Pro ac pair (Wireless Wire Cube Pro) for a specific use case. My primary goal is to achieve the lowest possible latency...
View ArticleBeginner Basics • Problem with VLAN and WebFig
Hi, this is my first time using RouterOS, so excuse me if this is a very basic question, but I can't find a solution, I've tried following a lot of tutorials but I keep having this problemI have set...
View ArticleWireless Networking • Can't connect HAP AC to CAPsMAN on CRS326
Hi folks, new to Mikrotik, so please have mercy... I have a CRS326-24G-2S+ and one HAP AC. The HAP AC (port 1) is connected to the CRS (Port 6). I can't get the HAP AC to connect to CAPsMAN on the...
View ArticleWireless Networking • Re: Can't connect HAP AC to CAPsMAN on CRS326
I was able to get it semi-working by activating CAPsMAN on the HAP AC itself. Then I noticed that the path to CAPsMAN is slightly different:It is "Wireless --> CAPsMAN --> CAP Interface -->...
View ArticleGeneral • Re: Dark mode on Dude and Winbox
Hi,Yes that's a dream to have dark mode on winbox.Statistics: Posted by dang21000 — Sun Feb 04, 2024 11:54 pm
View ArticleWireless Networking • Re: Assistance Needed with Cube 60Pro ac Pair for Low...
The most suitable frequency to use to minimize latency.353 THz (Math)Statistics: Posted by tangent — Mon Feb 05, 2024 12:51 am
View ArticleForwarding Protocols • Re: Multicast over OSPF/MPLS
PIM-SM is fairly stable on RouterOS v7 latest versions.It's likely a design/config issue on your end. Use VPLS to transport the layer 2, run PIM-SM on top of the tagged VLANs which rides on top of the...
View ArticleBeginner Basics • Re: Help with configuration of a port.
OK. So I ran up to this command:/interface list member add interface=ether9 list=WANBut I get this error:input does not match any value of interfaceI guess this is because there is not WAN interface...
View ArticleScripting • Re: Syntax difference in versions, how to handle?
Does :execute command exists in ROS6?You try with it if does, Code: :if ([/system package get 0 version] ~ "^6") do={:execute "/export terse" as-string} else={:execute "/export terse show-sensitive"...
View ArticleGeneral • using POE to power the CCR1009 on port 7
Hello,I'm looking for suggestions on how to power the CCR1009 via POE on port 7 as a backup for power.I'm thinking that I could use RBGPOE to power the CCR1009 via port 7 with a suitable power supply....
View ArticleScripting • Re: How should the local variable be called in if?
:log warning [$q] should not be: :log warning "$q"[] execute cmd/function, but you have a string/num.This is not the root cause, I just want to assign a value to the variable q and found that it is...
View ArticleBeginner Basics • Re: 100% CPU / Only CPU0 visable
IIRC on the System -> Resources dialog, there's a "Hardware" button. Can you try to click it and make sure the "Multi CPU" checkbox is ticked?cpu.pngStatistics: Posted by CGGXANNX — Mon Feb 05,...
View ArticleGeneral • Re: Bridge filter rules.. Dropping all devices except my access points
And how to do it for eg on L009 ? Is it better to use bridge filter rules or firewall rules ? I tried with bridge firewall rules to limit access to the port to only one MAC address but when I connect...
View ArticleGeneral • Faulty ethernet port
I have many rb-xxx wireless boards with faulty eth ports as they're used in outdoor units (atmospheric events, electrostatic discharge etc.) the rest of board is okDoes anyone know the common faulty...
View ArticleRouterBOARD hardware • The dream switch for the RB5009
Imagine the following switch:16x at least Gigabit ports including at least 8x PoE 802.3af/at2x 10G SFP+ portsSwOS, 802.1Q, management VLANThe size of two RB5009s one on top of the other, designed to...
View ArticleRouterBOARD hardware • Re: The dream switch for the RB5009
Hi,buy 2xRB5009 AND 2XRB5009 POE and you have your dream switch readyStatistics: Posted by Rox169 — Mon Feb 05, 2024 9:19 am
View ArticleWireless Networking • Re: Access Point Steering
I'm sharing my experience (also reported at viewtopic.php?t=203935): I have an ax3 and an ax lite, the ax lite is managed as an AP with CAPsMAN by the ax3 and shares the ports as a bridge. I tried to...
View ArticleWireless Networking • Re: Roaming/FT unexpected behaviour on 7.13.3
Just to share my experience, I tried different configurations but the best I found so far is:Code: /interface wifi securityadd authentication-types=wpa2-psk connect-priority=0/1 disable-pmkid=no...
View Article