Beginner Basics • Re: How do I setup NAT for multiple VLANs on different...
Yes of course! Just set it up more like a switch aka no need for dhcp, firewall rules etc....This should help with VLAN work............ viewtopic.php?t=143620and also the pointers given at this post...
View ArticleGeneral • Re: vrrp in firewall filter rules
Well, what you read may not be fully correct.VRRP is very special in its IP address setup. This has consequences for the traffic (did not read it but found out the hard way).Requests that come in via...
View ArticleBeginner Basics • Re: Slow network speeds with Pi-Hole as DNS
No ideas, and possibly unrelated, but how did you have the pi-hole as DNS server with the old "dumb" switch?Or if you prefer why do you need to specify it (and with the allow-remote-requests=yes) in...
View ArticleWireless Networking • Re: Cannot add smart lights to AX wifi
All I can add here is that some older devices just don't seem to work with Wi-Fi 6 even if you disable WPA3 PSK and stick with WPA/WPA2. For example, my ten year old Kindle can't even see the network....
View ArticleBeginner Basics • Recommendations on integrating my employer-issued MikroTik...
My home network consists of about a dozen VLANs. I have a dedicated (non-MikroTik) router, with each interface dedicated to a separate VLAN. Each interface serves DHCP from a subnet dedicated to that...
View ArticleGeneral • Port forwarding over ISP with enabled full network over wireguard...
I have a problem with port forwarding through my provider's link while my entire network is forwarded through wireguard to vpn.In the route list it redirects all traffic using Dst. Address and gateway...
View ArticleGeneral • Re: Port forwarding over ISP with enabled full network over...
In a nutshell, a. you use a third party VPN provider for one or more subnets going out wireguard.b. you also have servers on the LAN that(i) internal users use Q1. How do you prefer internal users...
View ArticleBeginner Basics • Re: Use public IPs from remote router
Established VPN of your choice, then use mangle or routing rules to route your internal subnet to the other side of the tunnel then use srcnat NATDo you have some examples of config?Statistics: Posted...
View ArticleWireless Networking • Re: hAP ax lite LTE : Wifi high latency
Hi,device is new.It has embedded antennas.Is there any check by the device to change frequency if there are too many interference ?After reboot, latency dropped to 15ms, that is still high compared to...
View ArticleRouterOS beta • Re: RB5009 Slow Speed 2.5G Bug Report (as requested)
On 5009UPr purchased in january 2024, Tested with 7.13 and 7.13.1 and the exact same problem continues to exist. Rx overflow counter is going up, no tx pause sent by the router and tx speeds _from_...
View ArticleBeginner Basics • Re: bridge or vlan after dot1x success
Did you finally figure it out ? what is your model of AT&T's router gateway, 5286AC or BG210, BG320 ?I am curious to know if there is a successful case to replace the AT&T RG, as it is said...
View ArticleThe Dude • How do I get the flag status
Hello,We have the Dude 6.48.1 running as a CHR in a virtual machine. Is there a way to get the flag status like how the Dude client displays a blue flag when all is good and a red flag when stuff is...
View ArticleScripting • Re: Max Concurrent Router to NAS FTP Download
Just a follow up on the above. It appears that since the APs are all trying to download the same file at the same time this is where the error may be occurring. Does anyone know if there is a...
View ArticleBeginner Basics • Re: Help: Edge switch between FW & ISP
From what I see in your config, you haven't defined the entry for vlan1000 in /interface bridge vlanYou need to define vlan1000 in there as well, like you have defined for vlan99.As you have indicated...
View ArticleWireless Networking • Re: Maximum MTU Size on virtual WiFi interfaces
Well, the screenshots on top of this thread are outdated. Between the creation of the topic and today, I did a complete reconfig of my system and all the MTUs are back to 1500 as the default setting....
View ArticleWireless Networking • Re: RouterOS does actively ignore IPv6 address from...
anyone? no idea?Statistics: Posted by WhileECoyote — Fri Jan 19, 2024 5:01 pm
View ArticleGeneral • Re: IPv6 ping no response - problem with my config?
I know this is an old thread but maybe someone will be searching for the solution to the same issue like I was last night...Basically in my case the end effects were pretty much exactly like OP...
View ArticleRouterBOARD hardware • Re: Is it mandatory to mount antennas on hAP ac3?
Yep, those are called "dummy loads", or "coaxial terminators", they have a SMA or RP-SMA (you need the RP-SMA kind or, additionally an adapter) connector and usually have 50 Ohm resistor...
View ArticleClik here to view.
Wireless Networking • Re: Ethernet AP with DHCP disable don't give mikrotik IP
I forgot that I had another access point connected via ethernet. It conflicted with the mikrotik's DHCP.I unplugged it, and now the D-LINK is sending back to the mikrotik's DHCP.I'll wait to receive...
View ArticleScripting • Re: Need help modifying a DHCP2DNS script
No replies yet, so I'm trying to figure this out myself.I've added a local variable dnsComment. Once the script has the dnsDhcpid, I try to use that to derive the comment set in the DNS entry. If...
View Article