General • Re: unable to install on usb drive ver 7.xxx
Hello! I do having the same freaking issue. Tried to install with WM but not booting on my x86 router.Statistics: Posted by kiloon — Sat Jan 06, 2024 5:49 pm
View ArticleGeneral • CRS328 + Cisco Aironet 1200 --> Access points will not power up
Hi,Has anyone got any experience with Cisco Aironet 1200 series (yes, I know these are ancient, but they still work for us and being a Scout campsite, we don't have limitless budgets for IT equipment...
View ArticleGeneral • RB3011 UiAS heavy slow down when using VLAN on SFP interface
Recently i did change my setup for Internet access.Previously i was connected behind a bridged provider Box through an RB3011 Ether1 interface, without VLAN. Using RouterOS 6.49.11.The Internet...
View ArticleRouterBOARD hardware • Default password not the one on the sticker after...
Hey,i know i know: read the instructions first or just read the frunking manual.But the new RouterBoard was so nice and shiny that i wanted to winbox it right away - and failed (because i did not pay...
View ArticleBeginner Basics • Re: Port forwarding through Proton VPN?
Wish I had more info for you on BTH, but normands was on vacation today and didnt answer my BTH questions LOL.Just noticed that there is a /ip/nat-pmp in RouterOS 7.13. It is not enabled by default....
View ArticleRouterBOARD hardware • Re: Default password not the one on the sticker after...
Problem solved: i read a 0 for a O.Though it might help some folks to mention that the Wifi password differs from the admin/password hardware login combination.If you want to find yours, go to...
View ArticleBeginner Basics • Re: Can't see Wireless Printer on phone connected Network
Update: I searched in the Microtik Haplite software and found the setting to allow all default forwarding. It took a while, because on this router the settings are found in a different place. After...
View ArticleRouterBOARD hardware • Re: Zerotier version on RB5009UG+S+IN and L009UiGS-RM.
1.10 has some speed improvements from my current 1.8.4 which is a good new. I ordered the RB5009. Thanks.Statistics: Posted by amb1s1 — Sat Jan 06, 2024 6:42 pm
View ArticleGeneral • Re: CRS328 + Cisco Aironet 1200 --> Access points will not power up
Very likely it is one of the (usual) issues with PoE standards (or non-standards and the way each manufacturer has implemented or not implemented them).The CRS328-24P-4S+RM is listed as being 802.3af...
View ArticleBeginner Basics • Re: RB5009 first time configuration questions
>I have UPnP enabled (mutiple PC gamers in house playing at all hours), where in the GUI can you see what ports have been opened via UPnP?Resolved UPnP issue, External Interface needed to be set to...
View ArticleClik here to view.
General • Re: USB serial remote monitoring and flashing
Also tried reading a serial with my RB951 . Works without problem, but I'm missing the option to upload the firmware over serial of RB951.Interesting ... Are you using special_login for...
View ArticleGeneral • Chateau LTE12 - Cell Monitor
When I run Cell Monitor, I am seeing the following LTE B28 appear:445B289360-104-18.0-762220B289360-105-19.0-762122B289360-107-20.0-779216B289360-107-20.0-762While I can connect to all the other bands...
View ArticleScripting • Re: 7.12.1 NAT Rule script bug
You are missing quotes.Try this:Code: /ip/firewall/nat/remove [/ip/firewall/nat find to-ports="1001"]Statistics: Posted by Jotne — Sat Jan 06, 2024 8:07 pm
View ArticleWireless Networking • Re: Persistent Wi-Fi Disconnection Issues with Mikrotik...
I have the same issue in two separate offices using the Hap Ax2 router. Some devices regularly disconnect for a few seconds. I never had this issue with my previous routers.Statistics: Posted by...
View ArticleClik here to view.
General • Under DNS Amplification attack, network unusable with Mikrotik routers
Hello everyone,We're having an issue at one of our clients, it seems that they have suffered a DNS amplification attack. There was port 53 udp open to the router (Mikrotik rb4011) from everywhere and...
View ArticleForwarding Protocols • Re: OSPF across Wireguard using ptp, not nbma?
Wojo........... If you are familiar with OSPFLooking to do something for failovers.Imagine 2 WAN inputs to MT router............. and a CHR on a VPS in the cloud.What I want to do is connect the two...
View ArticleBeginner Basics • Too many Wireguard logs from version 7.14beta3
I have a hEX S router and RouterOs v 7.13 beta 4 installed on it. I would like to point out that in the previous software version 7.13 beta 3 this problem also occurs, namely the running Wireguard...
View ArticleRouterBOARD hardware • Running out of space on 16MB RouterBOARDs
Hi,My HAP ac2 running on 7.13 is about to run out of space. Is Mikrotik aware of that? Maybe it would be a good idea to exclude ppp and routing from the main package bundle?ac2.pngStatistics: Posted...
View ArticleGeneral • pppoe customer login page
How can I redirect the http and https pages of my pppoe clients to a captive portal similar to that of hostpot?The objective is that when customers' service is suspended they are redirected to a page...
View ArticleGeneral • Recommended for IPS/IDS
Dear All,I am looking for a device doing DPI for home use. I have a lot of IoT devices which I have 0 visibilty on and decided to check what they are doing. They are in different VLAN, but still...
View Article