General • Re: How to exchange internet connection between 2 oficces.
Correct on the typo, should be 22 not 12, fixed up top!! Thanks.Statistics: Posted by anav — Sat Mar 23, 2024 3:47 am
View ArticleRouterBOARD hardware • Re: hEX POE (RB960PGS) can't mix 802.3af/at with...
https://mikrotik.com/product/rbgpoe_con_hp would solve your issue. Personally I prefer Ubiquiti's equivalent a lot more,the INS-3AF-I-G, it is the only Ubnt product I use, I like its form factor a lot...
View ArticleRouterBOARD hardware • Re: How to [not] blow a port on CSR328 (and a hex poe)...
Update:I received the magnetics module and successfully replaced it.Desoldering was fun due to "hundreds" of through hole little pins, but it wasn't too much trouble at the end.All ports work now!I...
View ArticleContainers • Re: Homeassistant as container and homekitbridge setup
i was able to configure it with bridge vlan filtering on main bridge and get it to work.Hardware offload turned off. switching speeds(same vlan iperf) dropped from about 950 to 880 Mb/sec .Routing...
View ArticleForwarding Protocols • Re: BGP Advertisement redundancy
I celebrated too soon hahaha, lost connnection a few hours after had to reverse the routeStatistics: Posted by aromerombit — Sat Mar 23, 2024 6:57 am
View ArticleRouterBOARD hardware • Re: CCR1036 Power Supply
I replaced my original power supply three years later after the purchase with a Mean Well EPS-65-24 and it has been working great for seven years.IMG00376.jpgMay i know "Mean Well EPS-65-24" can be...
View ArticleWireless Networking • Re: R11e-LTE6 modem firmware changelog
I don't see any difference between v36 and v20 from which I updated. However, version v38 has been available for a week, but I cannot update to it because the router throws it out:Code: >...
View ArticleVirtualization • Re: How to install Mikrotik CHR on Oracle Cloud always free...
I'm sorry that it didn't work for you.But I've done it multiple times and it does work.The video you are referring to, needs an account that CAN upload custom images,but when trial expires, this is...
View ArticleBeginner Basics • Subdomain redirection (NAT) to the local IP address.
Please help me redirect (NAT) the connection from outside HTTP/HTTPS so that after entering the subdomain, the connection will be redirected to a specific IP address and port in the local...
View ArticleVirtualization • Plan to port BTH to CHR?
Hi all,Is there any plan to port the BTH service to CHR routeros?Did you ear something about that?I've juste replace a RB5009 by a minipc under Proxmox/CHR and it's the only thing that I couldn't...
View ArticleBeginner Basics • Re: Subdomain redirection (NAT) to the local IP address.
You need reverse proxy for that like nginx or haproxy, you can do port forwarding on port 80 to a local reverse proxy from there handle the routing logicStatistics: Posted by loloski — Sat Mar 23,...
View ArticleGeneral • Dual-WAN PPPoE client
7.14.1 on RB4011iGS+ r2 (not complicated setup)Code: # 2024-03-23 10:05:45 by RouterOS 7.14.1# software id = 5WSQ-IVBW## model = RB4011iGS+# serial number = /interface bridgeadd arp=proxy-arp...
View ArticleBeginner Basics • Re: Mikrotik hAP ax3 - only one quick set mode
i have a similar problem with my HAP AC2 RDB52G.My router had the problem that after a power loss, the router didn't start correctly (also with winbox it wasn't seen). So I had to reset the router...
View ArticleGeneral • Re: Connect to router LAN side web interface from wireguard tunnel
In general one should set the Router ( assuming server for handshake ) the wireguard interface as part of the LAN interface, that then usuallly, through fw rules, allows RWs to access internet via FW...
View ArticleGeneral • Where's my bottleneck?
I'm running 7.14 stable on an RB5009, wired to an AX3 (also running 7.14). Most local clients connect via wifi to the AX3.I'm experiencing less than desirable performance and trying to figure out...
View ArticleGeneral • Re: Where's my bottleneck?
Have you thought of using IPERF for your testing??Statistics: Posted by anav — Sat Mar 23, 2024 3:27 pm
View ArticleWireless Networking • Re: CAPsMAN change of configuration without disconnect...
version and what it runs on shouldn't matter.I ran caps man on routers. Access points. Switches. Remote routers.Wherever I could find some sort of connections between WAPS and controllers.Connections...
View ArticleVirtualization • Re: Plan to port BTH to CHR?
What's wrong with simply configuring wireguard directly ?It's the basis of BTH ...just a little bit more bells and whistles.Statistics: Posted by holvoetn — Sat Mar 23, 2024 4:02 pm
View ArticleWireless Networking • Re: NetMetal5 to NetMetal AC² problem
You have to use Wave2 drivers on those AC2s.Ah, yes, because they work so well for PtPs.Statistics: Posted by FezzFest — Sat Mar 23, 2024 4:51 pm
View ArticleWireless Networking • Re: 7.14 wifi-qcom no superchannel?
just out of curiosity I tried to set different countries, maybe I didn't understand the limit well but it seems that the country limit is not respected (it is lower than the supported one).For example...
View Article