I am still struggeling and I reset again everything, even deleted storage and reflashed it (i am on RouterOS 7.13).
I wonder why such a simple thing doesn't work...
To show you exactly what I did after resetting I go now step by step:
1. Connected my client with Ether1 and connected to WinBox through the MAC adress of Ether1
2. After I had to change the password I went to the bridge menu and created a bridge with default settings
3. Then I went to Ports tab and created 3 ports, ether1 (where I am connected), ether2 (which will be my trunk port) and ether3 for testing.
4. Went to VLAN tag in Bridge menu and created my vlans - for now just default creation
My goal now is to put vlan20 on ether3 so I did:
5. edited vlan20 and put ether2 as tagged and ether3 as untagged
6. For the switch management I edited vlan10 and put ether2 and the bridge unter tagged
7. For the access port I went back to the ports tab in bridge menu, edited ether3 and changed under vlan the pvid to 20
8. For my management vlan I went to vlan tab in interface menu and created vlan10 with vlan id 10 and set the interface to bridge
8. Went to IP menu -> Addresses and created the address 10.0.0.6/28 and set the interface to vlan10 (network is set to 10.0.0.0).
9. For the default route I went to IP -> Routes and add a new route where I only put the Gateway 10.0.0.1
10. Then I add the same IP in the IP-> DNS tab
After that I have internet (can check for new updates), the time changed automatically and I also can ping any device behind the cisco switch.
But now I expected to put (any) client on ether3 and be able to get an IP from vlan20, but nothing works, no DHCP no static IP.....
What am I missing? vlan filtering is off right now btw, if i activate it on pvid 1 it also doesn't work, also cannot reach the switch from another vlan anymore...
I wonder why such a simple thing doesn't work...
To show you exactly what I did after resetting I go now step by step:
1. Connected my client with Ether1 and connected to WinBox through the MAC adress of Ether1
2. After I had to change the password I went to the bridge menu and created a bridge with default settings
3. Then I went to Ports tab and created 3 ports, ether1 (where I am connected), ether2 (which will be my trunk port) and ether3 for testing.
4. Went to VLAN tag in Bridge menu and created my vlans - for now just default creation
My goal now is to put vlan20 on ether3 so I did:
5. edited vlan20 and put ether2 as tagged and ether3 as untagged
6. For the switch management I edited vlan10 and put ether2 and the bridge unter tagged
7. For the access port I went back to the ports tab in bridge menu, edited ether3 and changed under vlan the pvid to 20
8. For my management vlan I went to vlan tab in interface menu and created vlan10 with vlan id 10 and set the interface to bridge
8. Went to IP menu -> Addresses and created the address 10.0.0.6/28 and set the interface to vlan10 (network is set to 10.0.0.0).
9. For the default route I went to IP -> Routes and add a new route where I only put the Gateway 10.0.0.1
10. Then I add the same IP in the IP-> DNS tab
After that I have internet (can check for new updates), the time changed automatically and I also can ping any device behind the cisco switch.
But now I expected to put (any) client on ether3 and be able to get an IP from vlan20, but nothing works, no DHCP no static IP.....
What am I missing? vlan filtering is off right now btw, if i activate it on pvid 1 it also doesn't work, also cannot reach the switch from another vlan anymore...
Statistics: Posted by yanndecay — Sun Jan 07, 2024 6:00 pm